How to fix a bent usb plug

Right, so I have this USB NES controller (a knockoff, not nintendo), and I think I must have stepped on it or set something heavy on it, because the metal outside of the usb is bent slightly so that it wont fit into the port. I looked down it and nothing seems to be out of place (not that I would know what it looks like normally, but I think its good). My question: Is there a good way to reshape it so it will fit into the port? It's not an expensive replacement, but I'd rather fix this one than buy a whole new one.

EDIT: Pics, forgot them in the original. First one is a normal USB, second is the controller. http://imgur.com/a/1aMkX

Thanks

Place needle-nosed pliers over the bent pin. Squeeze the ends of the pliers to apply pressure to the pins. Bend the pin back into place. If the pin is bent to the left or right, bend the pin back into the vertical position first, before adjusting it to the left or right.

How do you fix a bent USB?

First try to line the broken pins then firmly press the board to the connector. And insert your drive into the USB port.

How do you fix a bent micro USB cable?

So you might not even notice but it's bent slightly downward like that. So what you what you got to do right you can take a pair of pliers if you want or you know if you don't trust.

How do you fix a bent charger?

You want to chop little bits of this off to to sandwich in between the cable. Yeah then use a glue gun to stick it. And then you just tape it up with electrical tape.

Can you repair a USB cable?

If one of your cables begins to break, you can repair it using Sugru. Sugru – a mouldable glue formula – turns into rubber so your cable will last much longer and will prevent further breakages. Repairing a USB cable in place of buying a new one, is an inexpensive alternative to prolonging the life cycle of your cable.

Why do USB cables stop working?

Usually, USB cables stop working when they’ve been physically damaged (internal wires get bent or broken). Cheaper cables are made of lower-quality materials and aren’t as reliable or safe (especially for charging). If your cable breaks, you can repair it, but it’s far easier to replace it.

How do you rewire a USB cable?

How to Splice Two USB Cables Together

Cut the ends of the two sections of USB cable to splice with a pair of scissors. …
Place 1 ½ inch piece of heat-shrink tubing over one side section of cable. …
Remove 1 inch of the outer cover from the ends of the two sections of USB cable with the utility knife.

How do you fix a broken USB plug?

From one that has a good a end and possibly a damaged device and before a more professional look for just a few bucks you can get replacement USB ends so let's just solder one of these on.

How do I fix a bent USB C port?

Take a pair of needlenose pliers or a similar implement and use it to grasp the connector and straighten it by force. And then go to Amazon or wherever and order a new cable, as straightening the bent one is only good as a temporary repair.

How can I fix my fast charging cable?

How to fix fast charging not working on your device

Ensure you’re using the original charger and USB cable.
Switch to another USB cable.
Try a different fast charger.
Check the power outlet.
Try cleaning the charging port.
Close all running processes and allow the phone to charge.
Update your device.
Seek professional help.

Can you repair a USB-C cable?

Because recable is a repairable charging cable. With a few simple steps (and a few simple tools) you can easily repair it yourself. Why is this a good idea? By repairing your charging cable, you are doing something good for the planet.

How do you fix a slow charging USB cable?

So what you do is you take a safety pin a needle attack. And you poke it down in there to try to see if I have anything I can easier to point with. If you poke it down on poke it down in here.

A USB port is a type of connector used to connect a USB cable to a device. The USB port is compatible with a wide range of devices, including computers, smartphones, and tablets. The USB port is also backward compatible with older versions of the USB standard. The USB port is a popular choice for connecting USB cables to devices because it is easy to use and provides a secure connection. The USB port is also less likely to damage the device or the cable than other types of connectors.

If you’ve ever had the issue of your USB port being bent and not working properly, don’t worry, you’re not alone. This blog post will show you how to fix a bent USB port. First, look at the images below to see where the problem is located. Then, follow the simple steps we’ve outlined to get your USB port back up and running in no time.

Things You Will Need:

A flat head screwdriver
A needle nose plier
A pen or a paperclip

How to Fix Bent USB Port Step by Step Guide:

Step 1: Locate the Problem

The first step is to identify where the problem is located. Looking at the image above, you can see that the bent USB port is located at the top of the device. The problem is usually caused by the USB cable inserted into the port at an angle. This can cause the connector to become bent or damaged.

Once you have located the problem, you need to use a flathead screwdriver to pry the bent USB port gently. Be careful not to damage the surrounding area as you do this. You may need to use a little bit of force, but be careful not to break anything. If the port is severely bent, you may need to use a pair of tweezers or pliers to get a good grip on it. Once the port is raised, you can use the screwdriver to straighten it out gently. Again, be careful not to damage anything.

Step 3: Use a Pen or Paperclip

If the port is still not working properly, you can try using a pen or paper clip to straighten it out slightly. However, be careful not to overdo it, as you could permanently damage the port.

Step 4. Use a Needle Nose Plier

If the previous steps haven’t worked, you can try using a needle nose plier to gently grab the end of the USB connector and straighten it out. First, grab the USB connector’s end with a needle nose plier. Next, use your other hand to hold the body of the USB connector, so it doesn’t move. Finally, gently pull the needle-nose plier away from the body of the USB connector while keeping the end of the USB connector in place. This should straighten out the USB connector. If it doesn’t work the first time, try again.

Step 5: Try a Different Cable

If the port is still not working, you may need to try a different USB cable. Sometimes, the cable itself is the problem. Damaged or low-quality cables can cause many problems, including bent USB ports. If you have another USB cable handy, try plugging it into the port and see if that works. If it does, then you know the original cable was the problem. If it doesn’t, the port may be damaged and need to be replaced.

Step 6: Try a Different Computer

If you still have problems, you can try plugging the device into a different computer. This will rule out any software issues that may be causing the problem. If the device still doesn’t work, the port will likely be damaged and will need to be replaced.

If you’re still having problems, the next thing you can try is to update your USB device drivers. Outdated or corrupt drivers can cause all sorts of problems, so it’s always a good idea to keep them up-to-date. To update your drivers, you’ll need to know what kind of computer you have (PC or Mac) and what kind of USB device you use. Then, you can go to the manufacturer’s website and get the latest drivers. If you’re unsure how to update your drivers, you can use a driver update tool like Driver Easy.

Driver Easy will automatically scan your computer and look for the correct drivers for your devices. You don’t need to know anything about drivers; Find and install Driver Easy, then run it. It will do the rest. Once you’ve updated your drivers, restart your computer and try your USB device again.

Step 8. Use Device Manager

If your USB port is still not working, you can try to use the Device Manager to uninstall and reinstall the driver. This is how you do it:

Right-click on the Start button and select Device Manager from the menu.
Expand the Universal Serial Bus controllers section.
Right-click on the USB port that is not working and select Uninstall from the menu.
Restart your computer.
Windows will automatically install the drivers for your USB port.
Check if the issue is resolved.

Step 9. Use Clean Boot

If you’re still having problems, you can try to use Clean Boot to fix the problem. Clean Boot is a Microsoft diagnostic mode that starts your computer with minimal drivers and programs. This can help you troubleshoot if a program or driver is causing the problem.

Step 10. Test Your USB Port

Once you’ve tried all the above steps, it’s time to test your USB port. First, you’ll need a USB device you can test with, such as a USB flash drive or a mouse. Then, plug the device into the port and see if it works. If it does, then the port is working, and the problem is with your device. If it doesn’t, the port will most likely be damaged and need to be replaced.

Conclusion

This article has shown you how to fix a bent USB port. You can now fix your USB port without going through the trouble and expense of buying a new phone or laptop. All you need is some household items and a bit of patience. Have you tried this method yourself? Let us know how it worked for you in the comments below!